Draft Details

Designation:C22.2 NO. 250.13
Source:CSA
Review start date:Sep 13, 2019
Review end date:Nov 12, 2019
Categories:Electrical
Contact email:mary.morgan(at)csagroup.org
Draft Scope/Description:

1 Scope

1.1
The requirements specified in this Standard cover light emitting diode (LED) equipment that is an integral part of a luminaire or other lighting equipment, and which operates in the visible light spectrum between 400 and 700 nm. These requirements also cover the component parts of LED equipment, including LED controlgear, controllers, arrays, modules, and packages, as defined in this Standard.

1.1.1 LED controllers covered in this standard are intended to be:

Integral to the luminaire, or

Located remotely from the luminaire when the LED controller is supplied from and controls the luminaire using only Class 2 circuits.

1.1.2 These requirements do not cover the following LED controllers:

intended for installation inside a remote electrical outlet box containing Class 1 circuits, or

light-sensitive or presence-sensitive plug-In Locking Type Photocontrols for Use with Area Lighting covered by CSA C22.2 No. 284 and TIL A-15, or

solid-state dimming controls covered by CSSA C22.2 No. 184.1

1.2
These lighting products are intended for installation on branch circuits of 600 V nominal or less, in accordance with the Canadian Electrical Code, Part I, and for connection to isolated (non-utility connected) power sources such as generators, batteries, fuel cells, solar cells, and the like. 1.3

1.3.1
LED equipment is utilized in lighting products that comply with the end-product standards listed in this Clause. The requirements specified in this Standard are intended to supplement those in other end- product standards.

1.3.2
LED luminaires comply with the following end-product standards:

a) CSA C22.2 No. 207;
b) CSA C22.2 No. 12;
c) CSA C22.2 No. 89;
d) CSA C22.2 No. 141;
e) CSA C22.2 No. 166;
f) CSA C22.2 No. 9;
g) CSA C22.2 No. 250.0;
h) CSA C22.2 No. 256;
i) CSA C22.2 No. 250.7;
j) CSA C22.2 No. 1993;
k) CSA TIL B-31B; and
l) CSA TIL B-39.

Note: Where end-applications are not covered by this standard and no applicable end-product standards exist, additional end-product evaluations using applicable standards are needed. Such end-applications include but are not limited to LED equipment installed in air handling spaces or in other environmental air spaces (plenums), LED equipment in recessed installations where direct contact with thermal insulation may occur and LED equipment used in fire rated installations.

1.3.3
LED controlgear complies with the following end-product standards:

a)  CAN/CSA-C22.2 No. 223; and
b)  CAN/CSA-C22.2 No. 60950-1.

1.3.4
Requirements for Temperature Limited LED controlgear are specified in Annex G.

1.4
The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only.

1.5
In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.

You may comment on any section of this document by clicking the “Submit Comment” link at the bottom of the relevant section.